ASA Electronics VOM-58 Specifikace

ASA SERIES CLASS D AMPLIFIEROwners ManualPlease read through this manual to familiarize yourself with your new amplifi er. Should your PowerBass Auto-S

BATT+ (Power)This amplifier should be wired directly to the vehicle battery using the appropriate size cable. Start at the vehicle battery and run the

REM (Remote Trigger)This terminal must be connected to a switched +12V source. Typically, remote turn-on leads are provided at the source unit that wi

RCA INTERCONNECT WIRINGFig.5 Low Level Input using RCAChoose the correct length and style of RCA interconnects for your needs. Always use high quality

This control allows you to match the input level of the amplifier to the output level of your head unit. Matching the input can be accomplished in four

BASS EQ AdjustmentThis special feature is designed to provide you more powerful sound quality, and it allows you to increase the bass output up to +18

SPEAKER WIRING AND CONFIGURATIONSSpeaker LoadKeep in mind your PowerBass Autosound Class D amp is a high power amplifier and not a high current amplifie

Fig.11 A Single Voice Coil Subwoofer (1~4 ohm) Fig.12 Two 4 ohm Subwoofers with Single Voice CoilSpeaker Output Configurations1. A SINGLE VOICE COIL SU

3. ONE DUAL VOICE COIL SUBWOOFER SPEAKERS (Note: Don’t connect speaker impedance under 2 ohm)Fig.13 One Subwoofer (2~4 ohms) with Dual Voice Coil2-4 o

4. DUAL LINK AMP TO AMP BRIDGED CONNECTIONYou can connect two of the same model number ASA3 Series amplifiers and double the output power into a minim

SPEAKER CONNECTION FOR BRIDGING TWO AMPSThe mono woofer must be connected between the speaker (+) terminals of the two amplifiers and use at least #12

Thank you and CongratulationsThank you for your decision to purchase a PowerBass USA Autosound mobile amplifier! Our Autosound amplifiers are the resul

RECOMMENDED WIRE SIZESPower Cable Selection ChartFuse Total 4Ft 4-7Ft 7-10Ft 10-13Ft 13-16 Ft 16-19 Ft 19-22 FtIn Amperes Length of Wire/Gauge150A - 2

TROUBLESHOOTING TIPSProblem SolutionPower LED not ONWith a Volt Ohm Meter (VOM) check:• +12 Volt power terminal (should read +12 to +16VDC• Remote t

SPECIFICATIONS FOR AUTOSOUND D CLASS AMPLIFIERSPowerBass Autosound Class D Models ASA3-600.1D ASA3-1000.1D ASA3-1500.1DPower Output @ 14.4 VDC Input •

POWERBASS AUTOSOUND LIMITED WARRANTY POLICYPowerBass USA, Inc. offers limited warranty on PowerBass products under normal use on the following terms:P

PowerBass Autosound – A division of PowerBass USA, Inc.2133 S. Green Privado – Ontario, CA 91761Tel. (909) 923-3868 – Fax (909) 923-8048www.powerbassu

3TECHNICAL FEATURES• Mono Block Amplifier for Subwoofer• Latest Class D Technology• Double Sided Circuit Board Construction • MOSFET Power Supplies

INSTALLATION PRECAUTIONSNOTE: Proceed only if you are a qualified installer, otherwise; see your Authorized PowerBass Dealer to professionally install

5MOUNTING LOCATIONFind a clear and well ventilated area to mount your amplifier that is unobstructed by any objects that will cause harm or block venti

CONTROL PANEL LAYOUT1. POWER/STATUS IndicatorThe BLUE L.E.D. lights up when the power is on. This L.E.D. turns RED constantly or flashes when the built

74. GAIN ControlThis control is used to match the input sensitivity of the amplifier to the particular source unit that you are using up to 6 volts. Pr

12. BADGE SwitchControls the lighting of the top mounted PowerBass logo badge.13. SPEAKER Output TerminalsAs shown in the wiring diagrams, be sure to

9This amplifier is designed to work within a 9 to 17 volt DC range. Before any wires are connected, the vehicles electrical system should be checked fo